← Blog
8 March 2025·7 min read

Gears skipping or not shifting: a 5-step diagnosis

A skipping chain or slow, late shifting is frustrating but fixable. A guide to finding the cause — and when it is time to call the workshop.

Poor shifting is, next to a flat tyre and squealing brakes, the third classic of the workshop. And while a flat tyre has one cause — a foreign object — a derailleur that skips or does not respond can have six, seven or eight different causes, sometimes combined.

That is why gears need a systematic diagnosis, not random turning of screws. In the workshop we always go through the same order of checks — from the simplest to the most complex. Here it is.

Step 1: Check chain wear

The chain wears before the cassette and the chainring. A worn chain starts to 'ride up' on the cassette teeth instead of gripping them evenly. The result is skipping even with fresh cables and a perfectly adjusted derailleur. Many owners replace cables and adjust the derailleur, and the problem stays — because the cause is the old chain.

There is a special tool — a chain wear indicator — that shows in 10 seconds whether the chain needs replacing. A chain that has passed 0.75% stretch should be replaced before it passes the wear on to the cassette (a new cassette costs 3–5× more).

💡 Tip

Replace the chain every season if you ride regularly, or every 1,500–2,000 km. It is the cheapest investment in the health of your drivetrain.

Step 2: Condition of cables and housing

Gear cables stretch over time and corrode inside. The housing (the flexible sleeve that protects the cable) cracks, fills with mud or water and adds friction. The result: the derailleur reacts slowly, does not fully reach the smallest or the largest sprocket, or shifts back on its own.

Cables and housing are consumables that active riders replace once a year. Replacing a gear cable in our workshop costs 1,500 RSD on an MTB and 1,550 RSD on a road/gravel bike (same for front or rear), while cable plus new housing or internal routing through the frame is priced on site — always with fitting and adjustment. You feel it straight away — shifting becomes light and precise.

Step 3: Derailleur alignment

The rear derailleur is mounted on a derailleur hanger — a small aluminium part of the frame that bends in a crash instead of the expensive frame. The problem: the hanger also bends from small knocks and falls, and a bend of just 1–2 degrees is enough for the derailleur to miss the end gears.

Hanger alignment is done with a special tool and takes 10–15 minutes. If you have not crashed but have trouble with the end gears — this is a common culprit. Checking and aligning the hanger is included in our standard derailleur adjustment.

Step 4: Limit screws and the B-screw

Two small screws on the derailleur body ('H' and 'L') set how far the derailleur may travel in each direction. If the 'H' screw is too loose, the chain drops off the cassette into the wheel — a dangerous situation. If the 'L' screw is too tight, the derailleur does not reach the largest sprocket.

The B-screw sets the gap between the derailleur and the largest cassette sprocket. On modern 10-, 11- and 12-speed cassettes this gap must be within half a millimetre of the specified value — no more, no less. This detail separates a well-adjusted derailleur from one that skips in the last gears.

Step 5: Electronic groupsets (Di2, AXS, EPS)

Shimano Di2, SRAM AXS and Campagnolo EPS groupsets have no gear cables — they work electrically. That removes cable wear but brings new possible problems: low battery voltage, calibration in the app, firmware that needs updating.

An electronic derailleur that 'skips' almost always has a calibration or firmware issue. In the workshop we adjust electronic groupsets with the E-Tube (Shimano), AXS (SRAM) and My Gruppo (Campagnolo) apps. We set the price of an electronic derailleur adjustment on site, after diagnostics. If there is a firmware update waiting, we do it in the same visit.

💡 Tip

Electronic groupsets are extremely precise but they do not 'set themselves up' — the calibration has to be done properly. If you buy a used bike with Di2 or AXS, the first thing to do is a workshop check of the calibration.

Maintenance tips

Leave your email — we send useful tips.

No spam. Only practical bike service and maintenance advice.

NEED A SERVICE?

Diagnostics are always free. Bring your bike to Pinosava or we collect it anywhere in Belgrade — we check what it needs together and you decide what we do.

Bike repair in Belgrade — prices and bike pickup →