← Blog
20 August 2026·8 min read

Hydraulic brake service: bleeding and adjustment — everything you need to know

Hydraulic brakes need a fluid refill (bleeding) from time to time. We explain when it is needed, the difference between mineral oil and DOT fluid, and why it is not a job to improvise.

Hydraulic brakes are standard on every serious MTB and road bike — and for good reason. They give precise modulation, need less force at the lever and the bite point stays the same whatever the temperature. But they have one requirement mechanical brakes do not: the fluid that transmits the pressure has to be clean, free of air and at the right level.

Bleeding — the procedure of refilling the system and removing air bubbles — is not complicated if you have the right tools and knowledge. But done wrong, or with the wrong fluid, it can do more harm than good. Here is everything you need to know.

Mineral oil vs DOT fluid — the difference and why it matters

This is the first and most important thing about hydraulic brakes: they do not all use the same fluid, and you must NEVER mix the types.

Shimano uses mineral oil only (Shimano Mineral Oil). Tektro, Magura and some Formula brakes also use mineral oil. DOT fluid (DOT 4 or DOT 5.1) is used by SRAM, Formula (some models), Avid and Hayes. DOT systems have a higher boiling point — important for aggressive downhill riding — but are also harsher on rubber seals and need more careful handling.

If the wrong fluid has ever gone into the system, the brake has to be fully dismantled, cleaned and the seals replaced before refilling. That job is expensive and complicated — far more expensive than a regular bleed.

💡 Tip

Every hydraulic brake has its fluid type written on the lever or in the manual. Never assume — check before buying fluid or leaving the bike at a workshop.

Signs your brakes need bleeding

Hydraulic brakes do not always show clear signs of a problem straight away. These symptoms tell you a bleed is needed:

  • →The brake lever 'goes all the way' — it comes back to the handlebar without any resistance
  • →The brake 'gives' or the lever moves while you hold the pressure — a classic sign of an air bubble
  • →A soft or spongy lever — you feel there is no firm stop
  • →The brake works less well than before for no visible reason
  • →The lever does not return smoothly to its starting position
  • →You have replaced the brake hose or a component — the system must be bled after every such job

What happens during a bleed in the workshop

The bleeding procedure differs between mineral and DOT systems, but the general principle is the same. The mechanic connects syringes to the lever and the caliper, pushes fresh fluid through the system while the old fluid (with any air bubbles) comes out, and then closes the system with no trapped air.

For a Shimano mineral system this involves a special funnel on the lever and a syringe at the caliper. SRAM and other DOT brakes take a slightly different approach — usually bottom to top, because DOT fluid reacts aggressively with skin and the bike's paint.

Along with the bleed, an experienced mechanic always checks the brake pads, caliper alignment and the condition of the hose. At Bicikl servis Avala piston centring is always done together with the bleed.

How long a hydraulic brake bleed takes and what it costs

Bleeding one hydraulic brake in the workshop takes between 45 minutes and an hour and a half, depending on the system and the state of the fluid. For a pair of brakes, count on 2–2.5 hours.

A hydraulic brake bleed at Bicikl servis Avala costs 2,600 RSD per brake, the same for DOT (SRAM, Formula) and mineral systems (Shimano, Magura). The fluid is not included in the price of the job.

Can you bleed the brakes yourself?

Yes, you can bleed brakes at home — but it needs the right tools (syringes that fit your system, the funnel for Shimano, the right fittings and adapters), fresh fluid and patience. For DOT systems protective equipment is a must — DOT fluid damages the bike's paint and can irritate the skin.

If you are doing it for the first time, it is a good idea to have it done in a workshop first and watch the procedure. An improvised bleed (wrong tools, air not fully flushed out) can leave the system in worse shape than before. It is not a job to rush — it needs a steady hand and the right tools.

Maintenance tips

Leave your email — we send useful tips.

No spam. Only practical bike service and maintenance advice.

NEED A SERVICE?

Diagnostics are always free. Bring your bike to Pinosava or we collect it anywhere in Belgrade — we check what it needs together and you decide what we do.

Bike repair in Belgrade — prices and bike pickup →