A Kalkhoff Image 5 came into our workshop — an e-bike with a Bosch motor, an Enviolo hub gear and a Gates Carbon Drive CDX belt instead of a chain. The belt has 125 teeth. The job was adjusting the Enviolo hub: moving the hub to tension the belt correctly, checking that the hub uses its whole ratio range and restoring the full overdrive position.
This drivetrain is still rare in workshops here, but more and more German and Dutch e-bikes have it — so here is the whole procedure, step by step.
What Enviolo is and how it differs from a normal derailleur
Enviolo is a stepless (CVT) gear inside the rear hub. There are no gears 1 to 7 — turning the grip changes the ratio continuously, and you can shift while standing still. The full range of the Enviolo Trekking hub is about 380%: the hardest ratio is almost four times "taller" than the easiest.
The two ends of the range are called underdrive (easiest, for climbs and starting off) and overdrive (hardest, for fast riding on the flat). The grip is connected to the hub with two cables — one pulls towards underdrive, the other towards overdrive — through a part on the hub called the hub interface.
Gates Carbon Drive: a belt instead of a chain
A Gates CDX belt needs no lubrication, does not rust and does not stretch like a chain. In return it needs two things: exact tension and a perfectly straight belt line. A loose belt can skip a tooth under heavy load — and a Bosch motor delivers a lot of torque — while an over-tight belt loads the hub and motor bearings for nothing.
A belt bike has no tensioner like a derailleur bike. The belt is tensioned by moving the whole rear hub in the frame dropouts.
How the hub is moved and the belt tensioned
- →First the hub is shifted to full overdrive — the prescribed position for any work on the rear wheel.
- →The hub axle nuts are loosened.
- →The hub is moved back (more tension) or forward (less tension) — evenly on both sides so the wheel stays straight in the frame.
- →We measure tension with the Gates Carbon Drive app: the phone measures the belt's frequency when you pluck it like a guitar string. We measure several times while turning the cranks, because tension varies slightly along the belt.
- →We check the belt line: the belt must run straight between the front and rear sprockets and must not climb onto the sprocket edge when the cranks are turned backwards.
- →The nuts are tightened to the specified torque and the shift cable housings checked — they must stay free enough to follow the axle when it moves.
💡 Tip
If the belt squeaks or chirps after tensioning, the cause is almost always the belt line, not the tension. Never put chain oil on a belt — just rinse it with water when needed.
How the ratio range is checked
With the belt tensioned we check that the hub really goes through its whole range, from full underdrive to full overdrive. The bike is on a work stand, with a mark on the tyre and one on the frame.
- →Grip in full underdrive: one full turn of the cranks, counting how many times the rear wheel turns.
- →Grip in full overdrive: one turn of the cranks again, counting.
- →The ratio between those two numbers should be about the hub's range — roughly 3.8 times on an Enviolo Trekking hub.
- →If it is clearly lower, the hub is not reaching one end: the cables have the wrong length or too much slack, or the hub interface sits in the wrong position (usually after the wheel was removed).
How full overdrive is restored
If the hub interface is removed while the hub is not in full overdrive — when changing a tyre, for example — and refitted in another position, the hub loses part of its range. The grip shows the end, but the hub never reaches its hardest ratio. The fix:
- →The wheel comes out and the hub interface is removed from the hub.
- →The hub is brought by hand to the very end of its overdrive range: while the hub is driven in the riding direction through the rear sprocket, the hub interface is turned towards overdrive until a firm stop is felt. Repeat 2–3 times to be sure it is the end.
- →The hub interface goes back on in the full overdrive position, the wheel goes back in the frame and the belt is tensioned and checked again.
- →The cables are set to the right length with a little slack (with the barrel adjuster at the grip), so the grip and the hub reach their ends together.
- →Finally the range check by counting wheel turns is repeated.
Final check
After the adjustment the bike goes on a test ride: shifting standing still and while riding, a hill start in underdrive and riding up to 25 km/h in overdrive with the Bosch motor on. We check that the belt never skips on a hard start and that the grip moves through its whole travel without catching.
We set the price of this kind of adjustment on site, after free diagnostics — it depends on whether the cables need replacing and how far the hub is from its range. If your bike has an Enviolo hub or a Gates belt, book a slot and tell us the bike model.